Russound ST2 Manuale Utente

ST2 Smart TunerDual AM/FM TunerINSTRUCTION MANUAL

10ST2 SETUP AND CONNECTIONSANTENNA CONNECTIONSGrounding an OutdoorAntennaIf the tuner is used with anoutdoor antenna, the anten-na must be groundedaga

11ST2 SETUP AND CONNECTIONSCONTROLLER/AMP CONNECTIONS1RL21RL234CA6.4iNEWMARKET, NH U.S.A.~110VAC ~220-240VAC~50-60Hz400WVOLTAGE 110V220-240VFUSEF4AF2A

12++ST2 Tuner Side ViewRack Ear Front ViewRack Ear Side ViewRack Ear Screw HolesRack Mount InstallationThe ST2 tuner can be mounted in a standard comp

13Front Panel OperationTurning the unit onTo turn the unit on, push the On/Off button up on thefront panel. Pushing the On/Off button down turns thetu

14ST2 OPERATIONST2-RC REMOTE CONTROLST2-RC Remote Control OperationTurning the unit onTo take the ST2 tuner out of standby mode, pushPWR or any other

15ST2 OPERATIONUNO-S2 KEYPAD CONTROLS WITH CAV6.6CAV6.6-UNO-S2 Keypad OperationNOTE: To control the ST2 Tuner through theUNO-S2 keypad, the tuner must

16ST2 OPERATIONUNO-S2 KEYPAD CONTROLS WITH CAV6.6TUNER SELECTION - Select source numberassigned to TUNER 1 or TUNER 2FREQUENCY SELECT - Used for manua

17UNO-LRC1 Remote ControlOperationTurning the unit onThe tuner is power managed by the CAV6.6 or otherRNET-enabled controller. If the tuner is in stan

18ST2 OPERATIONUNO-LRC1 REMOTE CONTROL WITH CAV6.6POWER - Power managed by CAV6.6NUMERIC INPUT - Number buttons for directstation inputTUNE UP/DOWN -

19NOTE: The CAV6.6 and UNO-S2 firmware must be version 2.00.01 or high-er to control the ST2 Tuner. Use the System Info menu of the CAV6.6 tocheck the

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

20ST2 TUNER PROGRAMMINGPROGRAMMING FOR CAV6.6 USEMemory NameA memory preset must be created and savedbefore it can be named. Once it is saved, thepres

21Press and Hold TNR SEL buttonTUNER #BANK #MEMORY #MEMORY NAMESAVE CHANGES?Memory Name ProcedureTNRSELSelects characterSelects character positionRepe

22Bank NameA custom name can be assigned to each of thesix banks of both Tuner 1 and Tuner 2.1. Enter the Setup Menu by pressing and holdingthe TNR SE

23Press and Hold TNR SEL buttonSource Number, Region, Factory Initialization, Update Firmware and System Info ProceduresTNRSELTNRSELThis Procedureretu

24ST2 TUNER PROGRAMMINGST2 TUNER SETUP MENURegion (continued)1. Enter the Setup Menu by pressing and holdingthe TNR SEL button.2. Press MEM Up/Down un

25ST2 Smart TunerDimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)Weight: 7 lbs. (3.2kg)Power Supply: 12VDC 1.5AFrequency Range: AM

26WARRANTY & REPAIRThe Russound ST2 is fully guaranteed against all defects in materials and workmanship for two (2)years from the date of purchas

27NOTES

Russound5 Forbes Road, Newmarket, NH 03857tel 603.659.5170 • fax 603.659.5388e-mail: [email protected] www.russound.comE. & O.E.Copyright © 2003

3TABLE OF CONTENTSProduct Introduction ...4-

4INTRODUCTIONDESCRIPTIONThank you for choosing the Russound ST2 SmartTuner. Whether you are upgrading a legacy radio,expanding a CAi Series system, or

5INTRODUCTIONA-BUS® System - The ST2 Tuner can be used in an A-BUS systemwith an audio distribution hub such as the A-H484 and IR-repeating keypads s

6COMPONENT GUIDEST2 FRONT PANEL MAIN POWER SWITCH - Turns power on and offPOWER ON/OFF LED - Indicates power on or offREMOVABLE COVER LENS - Covers th

7RS-232INTERFACEIRLRAUDIO OUTPUT12VDC 1.5AIN OUTNEWMARKET, NH U.S.A.ST2 Smart Tuner LINK KEYPAD PORTSTUNER 1TUNER 2FM COAXLOOPANTENNAFM COAXLOOPANTENN

8TUNETUNEFAV 1SEEKST/ MONOLOC/ DXSEEKTUNETUNER 1 TUNER 24MEMBANK123567890PWRMEMTUNEAM/FMFAV 2OKPOWER - Puts the tuner in/out of standby modeTUNER CONT

9PowerTo power the tuner, connect the 12VDC externalpower supply to the unit by inserting the powersupply jack into the power supply connection onthe